Lectrosonics SPNTWB Bedienungsanleitung

Rio Rancho, NM, USAwww.lectrosonics.comFill in for your records: Serial Number: Purchase Date:SPNTWBTrio Conference InterfaceWideband BridgingINSTAL

SPNTWBLECTROSONICS, INC.10380 Ohms Pro gr amma b le Output Pi n 380 Ohms Programmable Output Pin1N4001 or equi v . Exte r na l DC V oltag eSource (&l

Installation and Startup GuideRio Rancho, NM11Software InstallationNOTE: Uninstall any previous version before installing the software.ASPEN Control

SPNTWBLECTROSONICS, INC.12Software and Firmware UpdatesOn ASPEN models with a front panel LCD, the firmware version is displayed on the Main menu scree

Installation and Startup GuideRio Rancho, NM135) Click on Next in the control panel and another page will open, allowing you to select the device to b

SPNTWBLECTROSONICS, INC.14Minimum SetupA required minimum setup is needed to allow the processor to pass signals and provide acoustic echo cancellatio

Installation and Startup GuideRio Rancho, NM15Output SourcesClick on the Output Source tab. These assignments pass the matrix mixes to the outputs.Pul

SPNTWBLECTROSONICS, INC.16The Signal Flow ScreenSelect the Signal Flow tab. This comprehensive, intui-tive interface allows settings to be made throug

Installation and Startup GuideRio Rancho, NM17Unused crosspoint columns can be hidden and unhid-den by highlighting a range of Mixes across the top, f

SPNTWBLECTROSONICS, INC.18Using the LCDThe LCD can be used to check current settings or make adjustments without using a computer interface.Boot Scree

Installation and Startup GuideRio Rancho, NM19After selecting the mode and/or changing the passcode, select SAVE with the rotary control and press the

SPNTWBLECTROSONICS, INC.2

SPNTWBLECTROSONICS, INC.20LCD Categories and SettingsINP (Input)• InputLevels• Mic/LineInputSetup• ConferenceInputSetup• TestSigInputSetup

Installation and Startup GuideRio Rancho, NM21Network SetupThe SPNTWB is IP addressable over an ordinary Ether-net network. The use of DHCP to configur

SPNTWBLECTROSONICS, INC.22Service and RepairIf your system malfunctions, you should attempt to correct or isolate the trouble before concluding that t

Installation and Startup GuideRio Rancho, NM23FCC PART 15 COMPLIANCE INFORMATIONThis equipment has been tested and found to comply with the limits for

5 November 2013581 Laser Road NE • Rio Rancho, NM 87124 USA • www.lectrosonics.com(505) 892-4501 • (800) 821-1121 • fax (505) 892-6243 •

Installation and Startup GuideRio Rancho, NM3This symbol, wherever it appears, alerts you to the presence of uninsulated danger-ous voltage inside the

SPNTWBLECTROSONICS, INC.4IntroductionThe SPNTWB combines the circuit board assemblies from the SPN812 and SPNCWB in a 2RU chassis to provide a complet

Installation and Startup GuideRio Rancho, NM5Table of ContentsIMPORTANT ...1I

SPNTWBLECTROSONICS, INC.6Headphone MonitorUsed to monitor individual final mix buses as selected on the LCD. Standard 1/4 inch jack and level control.

Installation and Startup GuideRio Rancho, NM7Rear PanelPower InletThe switching power supply will operate with line volt-ages between 100 and 240 VAC.

SPNTWBLECTROSONICS, INC.8Audio Inputs – UnbalancedUnbalanced audio sources include items such as consumer VCR’s, DVD players, etc., which can be con-n

Installation and Startup GuideRio Rancho, NM9Programmable InputsProgrammable inputs are provided to enable external control over a variety of paramete